News Details

Home > News >

Company news about Precautions when installing Electrical Braided Sleeving

Events

News

Mr. Ricky Wang

sales@huiyunhai.com

86-755-2803-2656

Contact Now

Precautions when installing Electrical Braided Sleeving

2025-07-31

When installing electrical braided sleeves, please note the following key points:

1. Pre-Installation Preparation

Dimension Verification: Measure the outer diameter of the wire harness and match it to the original inner diameter of the sleeve (recommended to leave a 20%-30% margin). Avoid overtightening, which may cause installation difficulties, or over-loosening, which may render the sleeve ineffective.
Environmental Inspection: Ensure the installation environment is free of sharp objects or high-temperature sources to prevent scratches or premature aging of the sleeve during installation.

2. Installation Procedures

Split Sleeve Installation: If using a sleeve with an opening, insert it slowly along the length of the wire harness to avoid forcible pulling that may deform the braid structure.
Securing Method: Secure the sleeve at both ends with high-temperature resistant cable ties or heat shrink tubing to prevent slippage and fall-off. The recommended spacing between securing points is no more than 30 cm.

3. Safety Precautions

Power-off Operation: Always disconnect the power cord before installation to prevent the risk of electric shock or short circuits.
Personal Protection: Wear cut-resistant gloves, especially when handling fiberglass sleeving to prevent fibers from piercing your skin.

4. Functional Integrity Testing

EMI Shielding Verification: After installation, use a multimeter to test the conductivity of the tinned copper braid to ensure shielding effectiveness has not been compromised.
Mechanical Strength Check: Manually pull the sleeving to confirm there is no movement or looseness, paying particular attention to the fit at the bends.

5. Special Scenarios

Installation in High-Temperature Areas: If the ambient temperature exceeds 200°C, pre-stretch the sleeving to accommodate thermal expansion and prevent contraction and compression of the wiring harness at high temperatures.
Corrosive Environments: After installing silicone-coated sleeving, seal the ends with sealant to prevent chemical ingress.

Tip: For complex wiring harnesses, it is recommended to install them in sections, with each section overlapping by at least 5 cm to enhance shielding continuity.

News Details

Home > News >

Company news about-Precautions when installing Electrical Braided Sleeving

Events

News

Cases

Precautions when installing Electrical Braided Sleeving

2025-07-31

When installing electrical braided sleeves, please note the following key points:

1. Pre-Installation Preparation

Dimension Verification: Measure the outer diameter of the wire harness and match it to the original inner diameter of the sleeve (recommended to leave a 20%-30% margin). Avoid overtightening, which may cause installation difficulties, or over-loosening, which may render the sleeve ineffective.
Environmental Inspection: Ensure the installation environment is free of sharp objects or high-temperature sources to prevent scratches or premature aging of the sleeve during installation.

2. Installation Procedures

Split Sleeve Installation: If using a sleeve with an opening, insert it slowly along the length of the wire harness to avoid forcible pulling that may deform the braid structure.
Securing Method: Secure the sleeve at both ends with high-temperature resistant cable ties or heat shrink tubing to prevent slippage and fall-off. The recommended spacing between securing points is no more than 30 cm.

3. Safety Precautions

Power-off Operation: Always disconnect the power cord before installation to prevent the risk of electric shock or short circuits.
Personal Protection: Wear cut-resistant gloves, especially when handling fiberglass sleeving to prevent fibers from piercing your skin.

4. Functional Integrity Testing

EMI Shielding Verification: After installation, use a multimeter to test the conductivity of the tinned copper braid to ensure shielding effectiveness has not been compromised.
Mechanical Strength Check: Manually pull the sleeving to confirm there is no movement or looseness, paying particular attention to the fit at the bends.

5. Special Scenarios

Installation in High-Temperature Areas: If the ambient temperature exceeds 200°C, pre-stretch the sleeving to accommodate thermal expansion and prevent contraction and compression of the wiring harness at high temperatures.
Corrosive Environments: After installing silicone-coated sleeving, seal the ends with sealant to prevent chemical ingress.

Tip: For complex wiring harnesses, it is recommended to install them in sections, with each section overlapping by at least 5 cm to enhance shielding continuity.

Electrical Braided Sleeving

PET Expandable Braided Sleeving

Tinned Copper Braided Sleeving

Stainless Steel Braided Sleeving

Self Wrapping Split Braided Sleeving

Braided Nylon Sleeve

Cotton Braided Sleeving

Zipper Cable Sleeve Braided Wrap

Velcro Cable Sleeve

Fishing Rod Protective Sleeves

Automotive Braided Sleeving

Flame Retardant Cable Sleeve

Flexible Braided Wire Covers

Heat Resistant Wire Sleeve

Abrasion Resistant Sleeving

Electrical Braided Sleeving

PET Expandable Braided Sleeving

Tinned Copper Braided Sleeving

Stainless Steel Braided Sleeving

Self Wrapping Split Braided Sleeving

Braided Nylon Sleeve

Cotton Braided Sleeving

Zipper Cable Sleeve Braided Wrap

Velcro Cable Sleeve

Fishing Rod Protective Sleeves

Automotive Braided Sleeving

Flame Retardant Cable Sleeve

Flexible Braided Wire Covers

Heat Resistant Wire Sleeve

Abrasion Resistant Sleeving

News Details

Company news about Precautions when installing Electrical Braided Sleeving

News

Precautions when installing Electrical Braided Sleeving

Company news about-Precautions when installing Electrical Braided Sleeving

News

Cases

Precautions when installing Electrical Braided Sleeving